Skip to content
EV Charging

Does My Panel Need an Upgrade for an EV Charger? 100 vs 200 Amp

By Joseph Myers · November 17, 2026

Request a Quick Quote

Free · No obligation · We respond same day

No spam. We respond within one business day.

A 200-amp panel usually handles a Level 2 EV charger. A 100-amp panel often does not. Here is how we check, and your options if it is tight.

Short answer: a 200-amp panel almost always has room for a Level 2 EV charger. A 100-amp panel often does not, but "often" is not "always," and the only honest way to know is a load calculation. Our crew does one on every charger quote, and about half the time a homeowner who assumed they needed a new panel turns out to be fine, while someone with a bigger panel is closer to the limit than they thought. The amperage printed on the main breaker is a starting point, not the answer.

What the number on your main breaker actually means

The main breaker rating (100, 150, 200) is the most current your service can deliver at once. A Level 2 charger is typically installed on a dedicated 40- or 50-amp circuit, which makes it one of the largest single loads in the house, right up there with central air and an electric range. The question is not whether there is a blank slot in the panel. The question is whether the whole house, running everything it reasonably would on a hot August afternoon, plus the charger, stays under the main breaker rating.

That is what a load calculation answers. It follows a method laid out in the National Electrical Code, which Florida adopts, and it accounts for:

  • Square footage (general lighting and receptacles)
  • Kitchen and laundry circuits
  • Fixed appliances: water heater, dryer, range, dishwasher, pool pump
  • Air conditioning, which in Palm Beach and Brevard counties is the big one
  • The proposed EV charger circuit

We run that math on a worksheet, and the permit office in cities like Boca Raton or Melbourne will want to see it when we pull the permit. If you have a 100-amp service with a heat pump, electric water heater, and electric range, the charger usually pushes it over. If you have gas appliances and a modest AC, a 100-amp service can sometimes carry a charger at a lower setting.

100 amps: the three usual outcomes

We see 100-amp services mostly in homes built before the 1990s: older neighborhoods in Cocoa and Rockledge along the river, the bungalows in Delray Beach, parts of Lantana near our office. When one of these needs a charger, the load calc lands in one of three places.

It fits as-is

Gas range, gas water heater, a single AC unit. The charger goes on a 40-amp circuit, the calculation clears, and we install it like any other job. This is less common than people hope, but it happens.

It fits with load management

This is the option a lot of homeowners have never heard of. Most Level 2 chargers can be set to draw less than their maximum, and some can be paired with a load management device that watches the whole panel and throttles the charger automatically when the AC or dryer kicks on. The code allows this approach, and it can keep a 100-amp home under the limit without touching the service. The trade-off is slower charging on the busiest evenings. For a commuter who plugs in overnight, that rarely matters.

It needs a service upgrade

Electric range, electric water heater, two AC systems, a pool pump. Add a charger and there is no math that works. At that point you are looking at a panel and service upgrade to 200 amps, which means a new panel, a new meter base in many cases, and coordination with FPL to swap the service. It is a bigger job, but it also solves the problem for good and leaves room for a second charger or a standby generator later.

150 and 200 amps: usually fine, with two catches

A 200-amp service on a typical single-family home in Viera, Wellington, or Jupiter has headroom for a charger in nearly every case we quote. Two things can still get in the way.

First, physical space. Some 200-amp panels are full, every slot used, and the only way in is a tandem breaker (where the panel lists it as permitted) or a small subpanel. Second, panel condition. We still run into aging panels and some brands with a known history of breaker failures. A charger pulling 40 amps for hours at a time is exactly the kind of sustained load that exposes a weak bus bar or a corroded lug, and in coastal homes near the Loxahatchee or the Lake Worth Lagoon, salt air makes that worse. If the panel is in rough shape, we will tell you before we add anything to it.

A 150-amp service sits in the middle. All-electric homes with two AC units can get tight, and we may recommend a lower charger setting or load management rather than a full upgrade.

What to ask before you sign

A proper EV charger quote should answer these without you prompting:

  • Did they do a load calculation, and can you see it?
  • What charger amperage are they proposing, and why?
  • Is a permit included, and who meets the inspector?
  • If an upgrade is recommended, is it because the math requires it or because it is easier to sell?
  • Does the quote cover the full run from the panel to the parking spot, including trenching if the panel is on the far side of the house?

If a contractor skips the load calculation and jumps straight to "you need 200 amps," get a second opinion. Sometimes that is the right call. Sometimes it is a few thousand dollars of work you did not need.

Whether you are in a 1970s ranch in Boynton Beach or a newer build off Malabar Road in Palm Bay, we will come out, look at the panel, run the numbers, and give you a free, no-obligation quote for EV charger installation anywhere in our Florida service area. Call (844) 432-2262 or send us the details online, and we respond within one business day.

Frequently Asked Questions

Can a 100-amp panel support a Level 2 EV charger?

Sometimes. It depends on the other loads in the house, which a load calculation determines. Homes with gas appliances are more likely to qualify, and a load management device or a lower charger setting can make it work in borderline cases.

Do I need a permit to install an EV charger in Florida?

Yes. A new 240-volt circuit requires an electrical permit and inspection in every county we serve, and the permit application typically includes the load calculation for the home.

Will upgrading to 200 amps also help if I add a generator later?

Usually, yes. A 200-amp service with a modern panel gives you room for a whole-home standby generator, a second charger, or a new AC system without going through another service change.